Synopsys Cloud
Cloud native EDA tools & pre-optimized hardware platforms
Request a Free Trial →
Synopsys offers a wide range of photonic simulation capabilities that cover device, circuit, and system level design. This article discusses modeling improvements made in late 2022 and early 2023 for circuit-level photonic simulations using the Synopsys OptSim product.
First, some background: photonic signals are quite complex in comparison to typical electrical signals used in IC design. Photonic signals can carry information in amplitude, phase, polarization, and spatial modes. Additionally, it is quite common to use multiple wavelengths of light to multiplex many signals onto a common waveguide. Lastly, for photonic IC (PIC) design, signal bidirectionality must also be understood as reflections within a PIC are quite common and can cause resonance and multipath interference. This complexity translates into modeling challenges for both the photonic and electrical domains.
Photonic devices in PICs are passive and active components. Passive elements are made from dielectric materials and are used to guide light. The propagation of light is influenced by the geometry and type of the dielectric material.
Active devices are made from semiconductors to facilitate energy transfers. In lasers, the applied electric field generates free photons, while in photodetectors, incident light generates free electrons. In modulators and active photonic filters, the applied electric field causes changes to the material’s refractive index, which also affects the optical signal’s phase and amplitude. This behavior can depend on wavelength, polarization, and temperature, and can be used to modulate light as well as to tune or select desired wavelengths.
Synopsys OptSim provides many tools for circuit-level photonic simulations; following are notable new features and modeling improvements.
Support for Analytical Equation-Based Data Files
Response functions for passive photonic devices such as arrayed waveguide grating (AWG) multiplexers, add, drop, or add/drop multiplexers, and components are typically modeled using a wavelength and mode dependent scattering matrix (S-matrix). All ports on the device are mapped to the rows and columns of the matrix. Ports are bidirectional, thereby allowing the model to represent a N´M port device in which stimulus at any port can contribute to a response at any other port, as would occur, for example, in components with internal reflections.
Synopsys OptSim has a primitive model for such a bidirectional multiport optical device. This model’s data can be derived either experimentally through measurement or through theoretical device-level simulations. The model supports single mode or multimode, unidirectional or bidirectional, and polarization sensitive or insensitive responses. The organization of scattering matrix data is conceptually shown in Figure 1.
Figure 1: S-Matrix Data for bidirectional, multimode, passive, NxM multiport optical devices
With increasing port counts, the size of the S-matrix data files increases because of the larger number of input-output relationships. For wideband, multimode optical devices with polarization crosstalk, the file sizes can become even larger. To overcome the potential problem of very large data files, Synopsys OptSim added a new option to support analytical equation-based S-matrix files in the v2022.06 release. The option parameter FileType selects between matrix- and analytical-equation-based data files.
Figure 2 summarizes the “Analytical” option. The second parameter, FileName, specifies a file containing either the wavelength-dependent scattering matrix, or a set of analytical equations for calculating the matrix.
Figure 2: New option for analytical equation-based S-Matrix data
Active Component Enhancements
Synopsys OptSim recently added model upgrades for active components:
- Support for equation-based and parametric-file-based voltage transfer equations in the Electro-absorption Modulator (EAM) model. EAM is a key component in high-speed transmitters. In addition to the parametric support for analytical modeling of an EAM, the new support now adds powerful capabilities for customization of nonlinear modulation response and chirp factor of the EAM via (i) analytical equations, (ii) data files, or (iii) polynomial fit to match observed behavior.
- New Photodetector Responsivity, Noise, and Frequency Response models. Breaking up behavior of a photodetector into functional blocks makes it easier to create a tailored photodiode response to match experimentally observed behavior.
- New 1×1 and 2×1 Optical Expression Signal Operator models. Sometimes it is required to create customized model behavior. To make this effort easier, two new models were added to Synopsys OptSim primitives. These primitives allow the model developer to write functional expressions that operate on the model’s optical input signals and the amplified spontaneous emission (ASE). The new models come in a 1×1 and 2×1 input to output configurations and can be combined in a schematic along with other OptSim primitives to enable modeling of more complex devices.
- Support for mixed-domain EO-co-simulation-based PDK models. This feature enables simulation of foundry PDK-based PICs having both electrical and photonic circuit hierarchies in the schematic. The mixed-domain simulation uses Synopsys OptSim for photonic circuit simulation and Synopsys PrimeSim SPICE/HSPICE for electrical circuit simulation in the same simulation run.
- New multi-channel support in EO co-simulation. This new feature allows simulation of foundry PDK-based electronic-photonic circuits comprised of PDK models that support multi-wavelength optical signals. It is especially useful when Synopsys OptSim is co-simulating with Synopsys PrimeSim SPICE using multi-channel Verilog-A models.
- New support for current-out-of-range warnings for Lookup Laser model. Behavioral models are helpful when physical parameters are unknown but measurements are available. The lookup laser model is a behavioral laser model where the LI curve is provided in a parametric file. The parameters are wavelength and temperature and they control the operating point. The input current is mapped into an output optical signal using parametric file lookup. During simulation, if the input current drops above or below the range in the data file, the model produces a warning alerting the designer of range violation.
Conclusion
In summary, multiple new modeling improvements have been added to Synopsys OptSim over the last two releases for E-O co-design of photonic circuits that contain electronic and photonic passive and active components and foundry PDKs. These improvements are customer driven and can be leveraged by all Synopsys OptSim users.
Continue Reading
Transforming PIC Design: How Synopsys OptoCompiler SaaS Platform Empowers PIC Start-ups
Mar 11, 2024 / 4 min read
Tags:
Photonic
